Iscar now offers a family of high-performance slitting tools that combine the convenience and security of Tang-Grip clamping with the added sturdiness of the completely new Sumo Tec insert grades.
The conception, already demonstrated successful in Tang-Grip parting tools, has now been extended to slitting cutters. In the patented Tang-Grip clamping system, inserts are press-fit into their pockets accompanying a special hand tool, and are held firmly in place without having the need without requiring clamps, upper jaws or set screws that can weaken the insert and hinder chip flow. The pocket configuration uses cutting forces to keep the insert seated solidly in position, eliminating any risk of insert pull-out. The Tang-Grip clamping system also fosters increased accurate slitting cuts plus increased pocket and insert lifespan.
Iscar's Sumo Tec insert grades feature a specific post-coating treatment which substantially improves tool life and constancy.
Introduced in late '07, the completely new Sumo Tec treatment flattens the insert's coated surface to dispose of microscopic stress raisers, decrease heat and friction and enhance chip flow. The result is improved toughness and resistance to chipping and built-up edge, all leading to enhanced tool life. The golden-colored flank on Sumo Tec inserts aides wear detection. Size for size, Tangslit cutters give more teeth than Iscar's SGSF cutters, permitting higher feed rates.
Their improved rigidity leads to straighter, increased accurate cuts and less vibration even in large-diameter cutters. The new Tangslit TGSF cutters come in 100 to 160 mm diameters, 3 and 4 mm widths and can accept the exact same selection of inserts as Tang-Grip parting tools. Additional sizes will be added.
Existing Sumo Tec grades for Tangslit cutters include:
IC808, with a tough submicron substrate below a Sumo Tec TiAlN PVD coating, providing superior resistance to impact loads and built-up edge. This grade is endorsed for slitting heat resistant alloys, austenitic stainless steel, hard alloys and carbon steel.
IC830, providing greater toughness for heavier parting and grooving involving interrupted cuts. It is fitting for any stainless steel & high temperature alloys.
IC908, a hard, fine-grain substrate with exceptional chipping resistance, joined with a new Sumo Tec TiAlN PVD coating. It is ideal for nodular or grey cast iron.
IC928 and 928A, PVD TiAlN-coated tough grades suitable for stainless steel, high temperature alloys and other alloy steels. These grades are also suggested for interrupted cuts and heavy operations.
Each Tangslit and Tang-Grip inserts are attainable in J- or C-type chipformer geometries from Iscar.
Iscar Adds Their Most Recent Innovations To A Extensive Line Of Successful Hole Generating Solutions
Iscar recently released several different drilling innovations to meet their customers needs. These new products are Sumocham Drill, DR-DH and Deep Drills. Drawing off of their experience Iscar has come up with new and innovative ways to increase productivity for the end user.
Various Progressions Have Enhanced Iscar's Families Of Indexable Endmills For Increased Productivity
Helido-Upfeed 04 Two years ago Iscar introduced the extremely efficient H600 indexable endmill line, based on conceptually new Helido-Upfeed double sided inserts with 6 cutting edges. The first insert launched was the H600 WXCU 0806..., which was designed for milling cutters in the diameter range of 50 to 125 mm.
Cutting Edge Tools And Carbide Insert Shapes From Iscar To Better Enhance The Machining Method
Iscar is introducing Penta 34 carbide inserts with a new PB chipformer. The PB chipformer features a single cavity with a positive rake, neutral shoulder angle, and a honed edge. It is actually a C-type chipformer with a different frontal edge.
The Most Recent In Carbide Endmill Designs In A Extensive And Productive Line From Iscar
Manufacturers and die & mold shops can eliminate chatter problems in many milling operations with Iscar's new Chatterfree endmills. The cutters' variable-pitch flute pattern eliminates harmonic vibration, the main source of chatter. This enables faster cutting and finer finish in rough or finish slotting, shoulder milling and cavity milling.
Push Pull Testing For Highway Industry With Calibrated Gauges. Stress Load Testing Procedures For On Site Evidence To Testing Standards.
Push Pull Testing for the Railway industry for proof of reliable anchor fixings. Calibrated push pull force gauges are used for stress load testing along with tensile strength pull testing procedures. Proof of load testing undertaken, measured, recorded in a reliable and standard way to BS5080 Part 1 standards.
Commercial Water Heater - Considering All Of Your Needs - Read Carefully To Learn More
Looking into a commercial water heater? Then you have a few things that you must consider. Take a look at these areas to avoid making a mistake with the wrong unit.
Totally New Rover Manufacturing Jobs
Britain's economy is trying to recover from the impact caused by the global economic recession through new Land Rover manufacturing jobs.
Related Articles
- Various Progressions Have Enhanced Iscar's Families Of Indexable Endmills For Increased Productivity
- A Couple Of The Several Advancements In Carbide Inserts From Iscar Over The Last Decade
- Cutting Edge Tools And Carbide Insert Shapes From Iscar To Better Enhance The Machining Method
- The Most Recent In Carbide Endmill Designs In A Extensive And Productive Line From Iscar
- Revolutionary End Mills By Iscar Can Multiply Productivity While Reducing Costs
Resources
Loading ...
